Mobile Phone Repairing Me PCB Par Jumper Kaise Banaye
2. Jumper Wire:
Mobile repair me jumper ek aisi technology hai jo mobile repair technician ke time or money dono ki bachat krti hai. PCB per bane track hum dekh nahi pate hai or Jab kisi part ka pcb per track ways broken ho jata hai to hum use ek hi trike se dobara jod skte hai or wo hai do parts ke bich me broken track ko jumper dwara reconnect krna. Mobile phone, Smartphone repair me ringer ways, speaker ways, vibrator motor ways, display screen ways, mic ways, led light, charging ways, small parts, ic or others all parts ke pcb per jumper banaye jate hai.
Kisi bhi mobile phone ki pcb board per jumper banana bahut hi easy hai. Iske liye sabse pahle pcb per broken track ko found kare or phir track ways kin-kin do parts ke bich me broken huaa hai, iska bhi pata kare. two broken parts ke connection ko reconnect krne ke liye ek patle jumper wire ko ek part se dusre part tk solder krke jodne ki technology ko ‘Jumper’ kahte hai. How to jumper in mobile phone repairing, Aaj ke lesson me aap jumper banana sikhenge. how to make jumper on mobile phone board. So aaj se, abhi se is ‘how to’ ko apne dil se nikal dijiye. Kyonki mobile repairing course se related aapka how to yani kaise kare ab hamesha ke liye gayab hone wala hai. Hum is mobile repairing course hindi website per full complete mobile repair course learning krwane ki koshish karenge.
Jumper banane ke liye jaroori Tools:
1. Soldering Iron:
Jumper wire ko parts per solder krne ke liye.
Mobile phone pcb per jumper banane or broke connection ko reconnect krne ke liye.
3. Soldering Paste:
Solder wire ko pighlane or soldering ko strong banane ke liye.
4. Solder Wire:
Jumper wire ko solder krne ke liye.
5. Multimeter:
PCB per track broken or kiye gaye jumper ko check krne ke liye.
6. PCB Stand:
Mobile pcb ko kaskar pkde rakhne ke liye.
7. Tweezers:
Jumper wire ko pakde rakhne ke liye.
8. Blade Cutter:
Jumper wire ki uper ki prt ko hatane ke liye.
9. Micro Soldering Iron:
Small parts per jumper wire ko solder krne ke liye.
How to Make Jumper - Jumper Kaise Banaye
How to jumper, any mobile phone ki pcb per jumper banane ke easy steps follow kare –
1. Mobile phone ke screw ko screw driver se khole (disassemble) or screw ek trf safe rakh de.
2. PCB ko carefully pcb holder/stand me set kijiye.
3. PCB per fault or broken track ko multimeter se check kare. jumper banana jaroori hai.
4. PCB per jahaa jumper wire solder krna hai un dono point per Soldering paste ko lagaye.
5. Jumper wire ko utna hi cut kare jitna un dono parts ke bich me length hai. Jumper wire ke dono traf ke point ki uper ki prt (lamination) ko hataye.
6. Ek hand me jumper wire ko tweezer me pakdkar pcb per pahle point per rakhe or soldering wire lekar soldering iron se solder kr de.
7. Isi prakar se dusre jumper wire ke point ko pcb ke dusre point per solder kr dijiye. Aap niche diye picture me dekhe jisme Battery connector ke positive pin se Boost coil tak jumper banaya gya hai -
8. Ab pcb per kiye gaye jumper wire ki testing krne ke liye multimeter se check kar lijiye.
Note: Mobile pcb per jumper banate samay yah dhyan rahe ki jumper points pcb ke pahle or last point per hi solder hone chahiye, points ke pas others parts per touch nahi hona chahiye. Jumper wire ki uper ki parat (परत) only shuru or end wale point se thora sa hataye jitne pcb point per solder ho sake.